High-quality standard pump of process-type
construction. Uncooled mechanical seal
equipped as standard shaft seal.
General specifications ranges
Dis. Pres.
up to 0.98MPa (10kg/m 2 ), 142psi
Suc. Pres
up to 0.5MPa (5kgf/cm 2 ), 71psi
Total head
up to 98m (321ft)
Capacity
up to 720m 3 /hr (3,170U.S.gpm)
Temperature
-10 to 80deg.C (-50 to 176deg.F)
Size
DN32 to 150mm (DN1 to 6in)
Stainless pump CPC/CPEN
Stainless steel pumps of process type (Back
pull-out construction).
Standard shaft seal type is mechanical seal.
No cooling is required up to the temperature
+140 deg.C.
General specifications ranges
Total head
up to 90m (295ft)
Capacity
up to 240m 3 /hr (1,060U.S.gpm)
Temperature
up to 140deg.C (284deg.F)
Size
DN32 to 150mm (DN1 to 6in)
For special requirements, including handing of heat
transfer oils, the CER pumps are available in various
constructions and materials. Please contact us
Process pump to
ISO2858 CPCN
Back pull-out design process pump to ISO
2858 having plenty materials / constructional
variation suitable for wide application
including in an intelligent building, a district
heating and cooling plant, in a power plant,
etc.
General specifications ranges
Dis. Pres.
up to 2.45MPa (25kg/cm 2 , 355psi)
Total head
up to 150m (492ft)
Capacity
up to 1,500m 3 /hr (6,600U.S.gpm)
Temperature
-40 to 180deg.C (-104 to 392deg.F)
Size
DN32 to 150mm (DN1 to 6in)
Double suction pump
CDM, CDMV
Both casing and bearings can be divided into
upper and lower portions to allow easier
disassembly for inspection. Pumps with large
diameters up to 2000mm are also
standardized. This pump with its rugged
construction and high efficiency, is most
suitable to feed various liquids at municipal
water works plants, steel plants, etc. Vertical
execution is also available.
General specifications ranges
Total head
3 to 700m (10 to 2300ft)
Capacity
90 to 36,000m 3 /hr
(400 to 158,500U.S.gpm)
Temperature
up to 80deg.C (176deg.F)
Size
DN150 to 2000mm (DN6 to 80in)
Multi-stage turbine pump
MMO, MMOV
Small-sized light multi-stage centrifugal pump.
The pump feet, integrally cast onto the
bearing housings, allow free orientation of
both suction and discharge nozzles. This ring
sectional multi-stage pump is used in
waterworks, pressure boosting stations,
sprinkling and irrigation installations, and
fire-fighting system. this pump is also used for
pumping boiler feed water and condensate,
for circulating cooling water and hot water,
and for the generation of power water.
Vertical execution is also available.
General specifications ranges
Total head
up to 400m (1310ft)
Capacity
up to 114m 3 /hr (505U.S.gpm)
Temperature
-10 to 140deg.C (-50 to 284deg.F)
Size
DN32 to 65mm (DN1 to 2 in)
High pressure
multi-stage turbine pump
MMK, MML
The axial thrust force of the MMK type is
balanced by the impeller balancing hole and
that of the MML type by the balancing disk,
so that the pumps can be driven with
complete safety at high speed. Axial suction
execution with special first stage impeller can
be adopted in case of severe suction
condition.
General specifications ranges
MMK
MML
Total head
up to 150m (492ft)
up to 500m (1640ft)
Capacity
up to 1,200m 3 /hr (5280U.S.gpm)
Temperature
up to 250deg.C (482deg.F)
Size
DN40 to 350mm (DN1 to 14in)
High pressure
multi-stage pump
MH series Axially split casing pumps
Radially split ring section barrel pumps
Radially split ring section pumps
Multi-stage centrifugal pumps having various
designs to meet the requirements in handling
feed water and condensate in power stations,
R.O. sea water desalination plant, etc.
General specifications ranges
Total head
up to 4,200m (13,800ft)
Capacity
up to 4,900m 3 /hr (21,580U.S.gpm)
Temperature
up to 230deg.C (446deg.F)
Size
DN40 to 450mm (DN1 to 18in)
Vertical multi-stage pump
MMTV
This pump is vertical barrel type pump with
specially wide suction inlets and specially
designed vanes. It can be installed at low
positions. As a result, this type is most
suitable for use as a condensate pump at
thermal power stations, where sufficient
suction pressure is not difficult to achieve
because of construction requirements.
General specifications ranges
Dis. Pres.
up to 3.92MPa (40kg/cm 2 )
Total head
up to 780m (2,560ft)
Capacity
up to 4,000m 3 /hr (17,610U.S.gpm)
Temperature
up to 200deg.C (392deg.F)
Size
DN40 to 500mm (DN1 to 20in)
Boiler circulating pump
HLV
HLV pumps and their driving motors from a
totally enclosed integral unit.
Water-filled three-phase motors (wet motors)
are used as drivers. These pumps are suitable
for high pressure, high temperature
application without any leakage due to no
shaft sealing part.
General specifications ranges
Total head
up to 320m (1,115ft)
Capacity
up to 6,000m 3 /hr
(26,420U.S.gpm)
Temperature
up to 420deg.C (788deg.F)
Size
DN40 to 200mm (DN1 to 8in)
Axial-flow propeller pump
IS, ISV
Widely used for applications with low head
and large capacity, this propeller pump is
simple in construction, almost trouble-free,
and highly durable for easier operation and
maintenance. Both fixed vane type and pitch
adjustable vane type are also available.
General specifications ranges
IS
ISV
Total head
1.5 to 5m (5 to 16ft)
Capacity
660 to 36,000m 3 /hr
(2,900 to 58,500U.S.gpm)
660 to 186,000m 3 /hr
(2,900 to 820,000U.S.gpm)
Size
DN400 to 2,000mm
(DN16 to 80in)
DN400 to 4,600mm
(DN16 to 184in)
Mixed-flow pump SP, SPV
Duplex
&
SuperDuplex.St. St
Widely used for application with large
capacity and higher head than IS, ISV model,
for intake of cooling water in power plants,
sea water in desalination plants and dock
drainage due to sea water resistant materials
(Ni-resist, etc.).
General specifications ranges
Total head
3 to 100m (10 to 330ft)
Capacity
600 to 78,000m 3 /hr
(2,640 to 343,500U.S.gpm)
Size
DN400 to 3,000mm (DN16 to 120in)
Vertical mixed-flow
volute casing pump
CFV
This vertical volute casing pump has a wide
head range, from low heads suitable for
mixed-flow pumps to high heads. The casing
is designed so that sewage cannot clog in it.
This pump can be spplied under both positive
suction head (+) and suction lift (-).
General specifications ranges
Total head
5 to 30m (16 to 98ft)
Capacity
3 to 150m 3 /min
(792 to 39,630U.S.gpm)
Size
DN200 to 1,000mm (DN8 to 40in)
In addition to the above operating range,
special and larger size pumps are also available
